Into The Woods 2023

.

Into The Woods 2023
Summary
Dates 4th - 9th December 2023
Location New Athenaeum
Creative Team
Director Louise Shepherd
Designer Alex Green
Lighting Designer Dylan McLean
Sound Designer Nathan Farndale
Video Designer Rhia Mitsuhashi
Production Team
Stage Supervisor Toby Cass
Deputy Stage Supervisor Nathan George
Stage Manager Robyn Johnstone
Deputy Stage Manager Iz Brett
Assistant Stage Manager Paola Soliz, Pim Unhasuta
LX Programmer Jamie Burke
PLX Dave Evans
Technical Stage Technicians Jacob Martin
Sound 2 Cara Slaughter
PSE Daniel Barclay

Technical Stage Department

Moon

Automated Movers

During the planning stages there was a requirement to move two moving lights IN/OUT to create a specific lighting effect on stage. We chose to use two BigTow winches to achieve this as it would give us the speed we needed but also the repeatably high accuracy every time. We also brought in black truss from NTS as when it flys in you can see the movers from the audience.

The effect desired was a physically moving beam of light, which then stays targeted on a single object centre stage. This then proved slightly harder than initially thought as when you press go on the auto cue, there is a period if time it takes to ramp up to the desired velocity and equally as is decelerates to come to a stop. The lighting programmer can plot a graph to which their cue runs to however we needed to know how long the acceleration and deceleration actually takes. We achieved this by plotting an AVD graph as seen below in Vectorworks, then using the tape measure tool to measure the length which equates to seconds.

I knew from the EpiQ desk that the accel was set to 1500mm/s^2. The velocity was 600mm/s. And the decel was set to 800mm/s^2. Total Cue time = 9.599s

So plotting a line from 0 (initial speed) to 1500mm over 1 second, then a constant at 600mm you can see where they intersect and draw a line down and measure from 0 again giving us 0.4 seconds. The same again for decel plotting 800mm over 1 second, intersection at 600mm, line down, measure to end of timed cue 9.599 seconds = 0.75s seconds. This plotted Trapezoid AVD graph is now to ramp up and down of that specific cue.

The LX programmer could then plot the exact same graph into the MA2 to achieve a smooth and linked* move.

Cameras

Due to the very busy wings on this show the automation desk couldn't go in a place with a clear line of slight of both automated set pieces. So it was positioned under the staircase that goes up to the USR platform. To overcome this issue we setup 3 serrate cameras around the set to monitor areas which might be affected when the set pieces are moving. The first (Top Right) is an overview of the stage, but facing predominately into the MSL wing as this is where the truss flys In to 1m. The second (Top Left) is a top down view of exactly where that truss is going to land, this is to make sure no-one or set is under it as it come to stage. The third (Bottom Left) is a camera placed above the moon balcony, this allows me to see that the doors on the moon are shut before it falls, and also to make sure that any crew of cast members are clear of it when quickly swoops away from the platform.

Sound

Comms

To connect our wired and wireless comms

- 3 Pin XLR out of wired comms basestation to in house patch

- From in house patch, XLR to 4-wire, into wireless comms basestation

To get wireless control pad

- Wireless basestation network settings

- Connect to basestations wifi

- Enter IP address in browser

Our settings

Meant that all wireless comms were constantly on B ring for our 'stage ring', but are still able to hear the DSM's show call.

Everyone on wired comms on A ring and are unable to hear wireless B ring.

B ring on wired comms was available too, separate wireless B ring, but are unable to hear the DSM.

Hollyland Solidcom C1 HUB8S Control Pad

A Group - Default B Group - Default

A Group - Changed B Group - Changed

Equipment and Power

Pit: Uses of power = 13amp and 16amp. Our DQ rack which distrobutes signal to the digico desk is powered by 16amp found in the upsatge left corner of the pit. we postioned our DQ rack at the front of the pit, DSL. This was because we had four subs on this show, two B1 - L + R and two C7 Subs - L + R. these were powered by amplifiers inserted in our DQ rack in the pit. We avoided long unwated runs of NL4(speaker cable) and were able to concentrate all of our cable runs at the front of the pit where easily accesible and out of the way of band memebers.

Nineteen microphones were used in our pit band. Microphone types included: DPA 4099 - Violins, Violas, Bass, Cello which were all attached using specific clips designed for each instruments. For example a violin clip:

Piccolo Snare Drum - AT2020 Snare Drum - AT2020 Bass Drum - SM89 Tom-toms - SE300 Cymbal (Suspended) - SE300 Small Choke Cymbal- SE300 Horn I - beta 57 Horn II - beta 57 Trumpet - MD441

Each instruments microphone is connected to the DQ rack in the inputs section via XLR cable. Once connected the digico SD12 in use is able to pick up their signal via dnate network. We used three stage boxes around the pit in order to control the amount of cable needed. See Image below.

Our main cable run was along the front of the situated steel deck we used bungies to attach the cables to the steel rungs. This was because it is fast and easy to attach, adjust-access cable, strike and is much more environmentally friendly than tape. The cables consisted of XLR, Cat 5 ethernet and power for our stage boxes

Some instruments it made sense to hang mics,The infrastructure of the pit allowed us to easily hang mics. See image below:

Pit PLan:

We layed black painted steel deck, this blacked out the grey floor in the pit, allowed us to manage cable runs better and added a certain elegance to the pit. We also rigged a black drape around the back of the pit to cover any unwanted storage.

In order for each band member to essentially have their own foldback we used a behringer powerplay system, beheinger base station connected to two distrobuters which distrobuters to each musicians powerplay unit, this small P16-M mixer allowed the musicician to switch between different groups within the mix. for example, strings Vox etc. Adjust volumes, pan, add effects etc. Headphones were required.

Onstage:

Photos

Behind The Scenes