Miscellaneous LX sundries: Difference between revisions
| (8 intermediate revisions by the same user not shown) | |||
| Line 63: | Line 63: | ||
== Boom Arms == | == Boom Arms == | ||
<br> | <br> | ||
'''48mm tube boom arms'''<br> | |||
[[File: Boom_arm_48mm_Scaff_.JPG |200px]] | |||
<br> | <br> | ||
We have a stock of 48mm aluminium pipe in the following lengths that can be used with a fixed 90degree scaff clamp to make a boom arm - '''THIS METHOD MUST NOT BE USED ON UPRIGHT TRUSS''' | |||
<br> 300mm x 7 | |||
<br> 400mm x 20 | |||
<br> 500mm x 16 | |||
<br> LUSTR x 10 (allow a Lustr to be outrigged from a boom with the fixture parallel to the arm without the DMX & Powercon fouling on the boom) | |||
<br> 800mm x 6 | |||
<br> 1000mm x 2 | |||
<br> | <br> | ||
[[File: Boom Arm Mix.JPG |300px]] | |||
File: | <br> These are stored in the grey tubs in the Ath LX store | ||
< | |||
<br> | <br> | ||
[[File: Boom_Arm_Storage.jpg |300px]] | |||
'''LX Dept Fixed 90deg Clamps For Boom Arms''' | |||
<br> These are marked with a spot of pink spray paint and live in a wheeled wooden box in the Ath LX store | |||
<br> [[File: Scaff_Clamps_LX_Dept.JPG|200px]] | |||
<BR> | |||
'''Doughty Twist Boom Arms:''' | |||
<br> | <br> | ||
[[File: Boom_Arm_w_Safety_Point.JPG |200px]] | |||
'''Boom Arm with safety bond attachment point - Stock x 11''' | |||
- USE THESE FIRST when rigging booms, or use these for units above head height | |||
<br> | <br> | ||
[[File: Standard_Boom_Arm.JPG |200px]] | |||
File:Standard_Boom_Arm.JPG | |||
'''Standard Boom Arm - Stock x 30 - Use for low units | '''Standard Boom Arm - Stock x 30''' | ||
- Use for low units | |||
<br> | <br> | ||
<br> | <br> | ||
---- | ---- | ||
| Line 116: | Line 138: | ||
File:City Theatrical Qorloflex 24 x 3a.jpeg | File:City Theatrical Qorloflex 24 x 3a.jpeg | ||
</gallery> | </gallery> | ||
<br> | |||
<br> | |||
Cable extension stock:<br> | |||
5 x 5m 5pin RGBW<br> | |||
6 x 10m 5pin RGBW<br> | |||
1 x 15m 5pin RGBW<br> | |||
6 x 5pin Plug to Pheonix connector for connection to bare ends on tape<br> | |||
<br> | <br> | ||
<br> | <br> | ||
| Line 247: | Line 276: | ||
6 x 2m<br> | 6 x 2m<br> | ||
<br> | <br> | ||
12v RGB+WW double row tape - encased in silicone - in 1m lenghts - NOT cuttable | 12v RGB+WW double row tape - encased in silicone - in 1m lenghts - NOT cuttable | ||
| Line 372: | Line 394: | ||
4 x 1m Hanging Fluorescent light fitting - essentially blue gelled fluorescent fitting - c/w hanging loop for verticle hanging, inline switch, and 13a plug | 4 x 1m Hanging Fluorescent light fitting - essentially blue gelled fluorescent fitting - c/w hanging loop for verticle hanging, inline switch, and 13a plug | ||
==LED Tape Fluorescent Fittings == | |||
[[File:LED Fluoro 1.jpg|200px]]<br> | |||
[[File:LED Fluoro 2.jpg|200px]]<br> | |||
[[File:LED Fluoro 3.jpg|200px]]<br> | |||
4 x 1150mm LED tape based Fluoro fitting. Has RGB + Cold White tape that is frosted/diffused to try and mimic a fluorescent tube. Tape is 12v @ 12.2w p/M so approx 15w per tube. <br> | |||
<br> | |||
<br> | |||
[[File:LED Twin Fluoro 1.jpg|200px]] [[File:LED Twin Fluoro 2.jpg|200px]]<br> | |||
<br> | |||
<br> | |||
4 x 1550mm LED tape based Twin Fluoro fitting. Has RGB + Cold White tape that is mounted to an egg crate diffuser to mimic a fluorescent tube. Tape is 12v @ 12.2w p/M so approx 20w per fitting. <br> | |||
Latest revision as of 15:29, 18 April 2023
Ladders
6 x Wire Rope Lighting Ladders
Total Hanging Length - 3m
Rung Width - 1m (1000mm)
Height Increments - 300mm
Top Steel Ends - Screwgate Hook/Karabiner
Bottom Steel Ends - Thimble Splice
SWL - 500kg
Standard setup is 4 rungs per ladder - we have 24 rungs total
https://www.ropeassemblies.co.uk/products/manufactured-assemblies/lighting-ladders/
Half Coupler
21 in stock - update 17/08/20
19 x Black and 2 x Silver -- SWL 100kg -- Uses M10 Bolt set
Unitrack FoH fittings
40 in stock - NB Uses M12 Bolt to mount lantern to TrackTamer
UniTrack Safety attachment for lanterns 30 in stock
Boom Arms
48mm tube boom arms
We have a stock of 48mm aluminium pipe in the following lengths that can be used with a fixed 90degree scaff clamp to make a boom arm - THIS METHOD MUST NOT BE USED ON UPRIGHT TRUSS
300mm x 7
400mm x 20
500mm x 16
LUSTR x 10 (allow a Lustr to be outrigged from a boom with the fixture parallel to the arm without the DMX & Powercon fouling on the boom)
800mm x 6
1000mm x 2
These are stored in the grey tubs in the Ath LX store
LX Dept Fixed 90deg Clamps For Boom Arms
These are marked with a spot of pink spray paint and live in a wheeled wooden box in the Ath LX store
Doughty Twist Boom Arms:
Boom Arm with safety bond attachment point - Stock x 11
- USE THESE FIRST when rigging booms, or use these for units above head height
Standard Boom Arm - Stock x 30
- Use for low units
Mirrorballs
1 x Large Mirror ball is currently available with a rotating mirror ball motor
2 x Small 40cm diameter mirror ball - no rotator
LED Tape Decoders
City Theatrical Qolorflex 24 x 3a - 12volt to 24volt input, 24 channels by 3 amps per channel. Housed in 8u rackmount flight case with 12v or 24v powersupplies built in. Unit has 6 x 5pin XLR outputs for 6 ways of RGBW colour control
www.https://www.citytheatrical.com/products/qolorflex-24x3a-dimmer
Qnty - 1
Cable extension stock:
5 x 5m 5pin RGBW
6 x 10m 5pin RGBW
1 x 15m 5pin RGBW
6 x 5pin Plug to Pheonix connector for connection to bare ends on tape
B078XS2SKH decoder - 12volt to 24volt input, 4 channels by 5 amps per channel
Qnty - 8
LT-8030 Decoder - 5v to 24v, 3 channels by 4 amps per channel
Qnty - 1
Decoder - 9v to 24v - 3 channels by 4 Amps per channel
Qnty 1
PX24500D Decoder - 12v to 24v - 4 Channel by 5amps per channel
Qnty 3
LED Power Supplies
Meanwell 12v LPV-100-12 100watt 12volt power supply unit
Qnty - 9
Triac Dimmable Constant Voltage LED Driver
30watts at 24volts
Qnty 2
This is a PSU that you can dim via a normal dimmer to dim 24v LED products without needing a DMX decoder
Tagra Orion-D-48/24v Triac Dimmable Constant Voltage LED Driver
48 watts at 24volts
This is a PSU that you can dim via a normal dimmer to dim 24v LED products without needing a DMX decoder
LED Tape
12v RGB+ WW & CW (also called RGB + CCT) - NOT CUTTABLE - lengths currently available:
6 x 0.5m
6 x 0.75m
6 x 1m
6 x 2m
12v RGB+WW double row tape - encased in silicone - in 1m lenghts - NOT cuttable
qnty - 6 x 1m length
12v RGBWW IP65 tape - silicone encased - RGB plus a WW separate chip - 5m lenghts - NOT cuttable
qnty 5 x 5m reel
12v RGB IP65 tape - silicone encased - in 5m lengths on reels - NOT cuttable
qnty 3 x 5m reel
12v RGB IP65 tape - silicone encased - RGB in 2m lengths - cuttable
Qnty 12 x 2m section
12v RGB IP65 cuttable tape - currently in 2m sections
Qnty 3 x 2m section
24v RGBWW - IP56 splash proof - cuttable to specific lengths - current stock 4m white plastic reel
Qnty 1 x 4m reel
24v RGBWW - IP56 splash proof - NOT cuttable on BLACK plastic reel
Qnty 1 x 3m reel
Mini strobe
1 Strobe QK75S
Fairy Lights
11 x 7.5m white string (3 pin interlinking cable) - REQUIRES PURCHASE OF 24V PSU from "Lights for Fun"
4 x 9m long white string with 14 drop strands 2.5m length - c/w 13a plug adapter
Festoon
15m Length - 50cm lamp spacing x 4
10m Length - 50cm lamp spacing x 1
10m Length - 75cm lamp spacing x 2
8m Length - 75cm lamp spacing x 1
Neon Flex - 50cm batten
5 x 0.5m length of white Neon flex mounted on timber as short batten type light source - Requires 24Volt driver
Blue Hanging Fluorescent
4 x 1m Hanging Fluorescent light fitting - essentially blue gelled fluorescent fitting - c/w hanging loop for verticle hanging, inline switch, and 13a plug
LED Tape Fluorescent Fittings
4 x 1150mm LED tape based Fluoro fitting. Has RGB + Cold White tape that is frosted/diffused to try and mimic a fluorescent tube. Tape is 12v @ 12.2w p/M so approx 15w per tube.
4 x 1550mm LED tape based Twin Fluoro fitting. Has RGB + Cold White tape that is mounted to an egg crate diffuser to mimic a fluorescent tube. Tape is 12v @ 12.2w p/M so approx 20w per fitting.